Acetylene hook up

acetylene hook up

How do you set up an oxy acetylene torch?

How to Set Up an Oxy-Acetylene Torch. Turn the valve on the acetylene tank counterclockwise a quarter turn to open. Adjust the acetylene regulator until the small gauge on the regulator registers 10 psi. Open the oxygen valve on the torch handle completely by turning counterclockwise until it stops.

How to install oxygen and acetylene tanks?

1 Secure the oxygen and acetylene tanks in the torch cart. ... 2 Remove the covers protecting the tank valves and attach the regulators to the valves. ... 3 Attach the hoses to the regulators. ... 4 Connect the other end of the hoses to the torch handle. ... 5 Turn the valve on the oxygen tank completely open. ... More items...

What is the best way to store oxygen and acetylene?

Oxygen and Acetylene are stored under pressure in steel cylinders. They are sized by the cu ft of either Oxygen or Acetylene that they hold. Cylinders should be tested regularly with the date of the last test stamped on the top of the cylinder. Cylinders should always be secured and used in the upright position.

How do you connect oxygen and acetylene hoses together?

Attach the hoses to the regulators. Connect the green hose to the oxygen regulator and the red hose to the acetylene regulator. Connect the other end of the hoses to the torch handle. Push the cutting torch in to the torch handle and hand-tighten the nut. Close the valves on the torch handle and the cutting torch.

How do you adjust the oxygen on a acetylene torch?

Adjust the acetylene regulator until the small gauge on the regulator registers 10 psi. Open the oxygen valve on the torch handle completely by turning counterclockwise until it stops. Slightly open the oxygen valve on the cutting torch. Open just enough to start the flow of oxygen through the torch.

How to install oxygen and acetylene tanks?

1 Secure the oxygen and acetylene tanks in the torch cart. ... 2 Remove the covers protecting the tank valves and attach the regulators to the valves. ... 3 Attach the hoses to the regulators. ... 4 Connect the other end of the hoses to the torch handle. ... 5 Turn the valve on the oxygen tank completely open. ... More items...

Why do my oxyacetylene torches keep going out?

It keeps the acetylene from mixing in the hoses and tanks with the oxygen and vice versa. Thanks! Why do the torches keep going out? The work is dissipating heat faster than the torch is producing it. Turn up the torch or use a larger tip. Thanks! Can you provide a list of procedures for adjusting an oxyacetylene torch for brazing?

What is an oxy acetylene torch used for?

An oxy acetylene torch is an affordable and versatile tool used by many people to heat, weld, solder, and cut metal. It uses extreme heat to function, and setting it up properly is one of the most important steps in using it safely.

How do you connect acetylene and oxygen to a torch?

Connect the acetylene hose to the acetylene regulator and to the torch. Sometimes the torch doesn’t specify which connection is for the acetylene, though the oxygen will be clearly marked. Whichever connection is not for the oxygen is for the acetylene.

How do you transport oxygen and acetylene cylinders?

Fasten oxygen and acetylene cylinders in an upright position. If you have a cylinder cart, place both the oxygen and acetylene cylinders into it. If not, they should be securely fastened with a chain to a workbench, a wall, or a post.

How to choose the right gas welding hose?

The choice of the right connection type will depend on your application requirements. It is always recommended to use the right hose connection for your gas welding hoses, preferably sourced from the manufacturer of the equipment. Rexarc is one of the leading manufacturers of acetylene gas plants and gas cylinders in the US.

What happens when you mix oxygen and acetylene together?

When oxygen and acetylene are mixed in right proportions within a blowpipe or hand-held torch, they can produce a very hot flame, with a temperature as high as 3,200 degrees. This temperature is hot enough to melt all types of commercial metals. As you change the ratio of the two gases used, the action of the flame is adjusted.

Related posts: